DeWALT DW723 Black Friday Sales!
 |
DeWALT DW723 Black Friday Sales!.
Product: DeWALT DW723 Amazon Price: Too low to display Availability: In Stock |
Compare Prices on DeWALT DW723
This is a splendid product with some flaws.
The Good:
Very portable and snappy and easy to situation up.
It is stable (distinguished more stable than it looks) .
Long adjustable supports.
Flip stops are handy for repetitive cuts.
The notice - quite reasonable when you search for at the competition (or even the previous version of this stand) .
The Bad:
The biggest scrape is that the supports are objective too microscopic. Yes you can situation the attend 12' from the blade but there is no wait on in between. This is a pickle when squaring the ends of 16' mdf moldings - they really sag. Cutting mdf moldings suitable is even worse - a little bend in this scenario results in the molding falling of the front or relieve of the befriend.
The supports adjust easily to match the height of your saw. The predicament? Understanding on adjusting them constantly because they will not finish save. Also the beams that the supports sit on have some wiggle room to allow them to bolt in and out. At plump extension the beam can be proceed as mighty as 3/4" up or down
My review is somewhat negative because I wanted potential buyers search for both sides - all the handsome reviews conceal some flaws. However, I calm really admire this stand. You can not beat the portability of this stand. The problems I have found have been solved in some other stands but those things are unbiased titanic beasts. The portability is far more vital to me. Also the stiffer your material the better. The stand really shines for rough carpentry - where little variances with the stops don't matter, the height of the supports can be off a bit, and the material is straight enough to not tumble off the encourage or sag in between. I have often slice 4 x 12's for headers (as long as 14') and the stand held the up perfectly.
Most of my grievances only arrise when using MDF moldings. The fact that I do so regularly is probably the biggest factor in my 3 star rating.
In case you were wondering - I'm a contractor and I have worn this stand almost every day for about 18 months.
I've have nick my fraction of board feet while squating in front of my miter saw while it was on the floor. As I fetch older, this was going from being inconvenient, to a loyal injure in the befriend. (Literally!) There was no plot to relieve the ends of the board other than shimming with scrap gallop prior to each chop. I tried mounting it on top of my B&D Workmate, but supporting the ends of the boards became even more of an recount. I knew I wanted a mitersaw stand, but which one?
I liked different features of the different stands I reviewed, like gargantuan wheels, heavy construction and additional work supports. Some looked like I could copy their produce and weld from square tubular steel. Weight would be a consideration. Combine this with the weight of the saw, it could be over 160 pounds. Getting it into and out of my SUV without trashing my bumper (and my aid) would be a trick. Using aluminum rectangular tubing would be lighter, but really pricey! After looking at the others, I decided on the Dewalt 723. I am satisfied I did! Most of the others reach in kit create, the 723 is fully assembled. It folds into a compact package, is relatively light, very sturdy, made from high quality components, and it is one of the most professional looking stands around (especially when mounting a matching Dewalt miter saw on it!) .
Most bolts have Allen-wrench heads. Any that are adjusted often (such as the extention arms and supports) have sizable T-handles. All nuts are the type that have nylon lock-washers to sustain from vibrating loose. The saw brackets assign (and detach) posthaste from the main beam. There are rubber feet attached to the brackets so the saw can be ragged alone on a bench (or on the floor...) if desired. The arms will serve 99.5% of the straggle I will be chopping without sagging. When I want to throw an 8' 4x12 on the stand, it will require supports (2x2s will do) clamped to the arm, extending down to the ground. Other stands have these extra supports already attached, but are unneccessary for the immense majority of my cuts; and will only add to the weight and complexity of break-down for transport.
By folding down my rear seat of my SUV, I can accept the stand to fit with ease. The saw is collected, and placed next to it. I will probably achieve a pair of 10" phenumatic wheels to one ruin for easier protability around a job region. I like the table saw extention the Delta folks have on their stand (model 50-155), and will incorprorate a slight extention similar to theirs on the DW723. There are some cheaper stands around, but they were either too heavy (up to 90 lbs for the stand alone!) or too flimsy (for mounting a DW708 12" compound sliding miter saw) . The package arrived in magnificent shape with no hurt to the stand.
I highly recommend this stand. Now that I have one, I wonder why I didn't accumulate one sooner. I'll never go succor to squating on the floor again.
Let me say up front that if I owned a DeWalt miter saw, I'd give this stand a perfect 5.
As a previous reviewer brought up, the Makita saw is a bit deeper, and for some reason the rear mounting holes are inset from the front mounting holes. No plight if you are resourceful, and have a slight angle iron on hand. Being able to adapt additional mounting rails to a variety of tools could perform this an extremely versatile tool. Imagine unclipping your miter saw, and dropping on a tablesaw, bandsaw, or sander, with each swap taking less than 30 seconds!
After I fabricated a few mounting rail extensions for my Makita, the saw dropped onto the mounting rail like silk! There's a lot to like about this stand. It is immediately solid, and no hint of being tipsy even when the sawhead on the 12" saw is locked to the rear place.
I was concerned that the extensions would be too flimsy to befriend a long deck board, but after I leveled the extension to the table (more on this later) it was very solid, and sliding the 2x6x12 serve & forth as when you are aligning a sever tag, there was very puny deflection or bouncing.
After I initially mounted the saw, I found that the Makita table is higher than the supports will go. I conception to modify a dwelling of my contain accomplish to match my saw. DeWalt may have balked at making a more universal deplorable, but the fact is there are a LOT of different brands of saws out there and only a handful of quality tables available. Don't know about the grand boys, but I've never turned up my nose at a potential revenue stream!
In the folded site, the stand is a itsy-bitsy pudgy, especially after hoisting 2x goods all day, but not too unpleasant. From the time the stand comes off the truck to location up & ready to work, has been as swiftly as 2 minutes! I don't mediate the Trojan can be plot up that expeditiously, and that table is very tipsy with a 12" saw mounted to the rear of the table.
If you have a DeWalt saw, this stand is a no-brainer. If you have a different mark of saw, I'd narrate taking the time to gain a plywood obnoxious as instructed by DeWalt to mount your particular saw. This one is tough and ready to go to work lawful out of the box.
Gay Cutting!
